Search results

Selective laser sintering (SLS) is one of the most rapidly growing rapid prototyping techniques (RPT). This is mainly due to its suitability to process almost any material: polymers, metals, ceramics (including foundry sand) and many types of composites. The material should be supplied as powder that may occasionally contain a sacrificial polymer binder that has to be removed (debinded) afterwards. The interaction between the laser beam and the powder material used in SLS is one of the dominant phenomena that defines the feasibility and quality of any SLS process. This paper surveys the current state of SLS in terms of materials and lasers. It describes investigations carried out experimentally and by numerical simulation in order to get insight into laser‐material interaction and to control this interaction properly.

The purpose of this paper is to compare different powder metallurgy (PM) processes to produce ceramic parts through additive manufacturing (AM). This creates the potential to rapidly shape ceramic parts with an almost unlimited shape freedom. In this paper, alumina (Al₂O₃) parts are produced, as Al₂O₃ is currently the most commonly used ceramic material for technical applications.

Variants of the following PM route, with indirect selective laser sintering (indirect SLS) as the AM shaping step, are explored to produce ceramic parts: powder synthesis, indirect SLS, binder removal and furnace sintering and alternative densification steps.

Freeform-shaped Al₂O₃ parts with densities up to approximately 90 per cent are obtained.

The resulting Al₂O₃ parts contain inter-agglomerate pores. To produce higher-quality ceramic parts through indirect SLS, these pores should be avoided or eliminated.

The research is innovative in many ways. First, composite powders are produced using different powder production methods, such as temperature-induced phase separation and dispersion polymerization. Second, four different binder materials are investigated: polyamide (nylon-12), polystyrene, polypropylene and a carnauba wax – low-density polyethylene combination. Further, to produce ceramic parts with increased density, the following densification techniques are investigated as additional steps of the PM process: laser remelting, isostatic pressing and infiltration.

This paper provides an overview of the different binding mechanisms in selective laser sintering (SLS) and selective laser melting (SLM), thus improving the understanding of these processes.

A classification of SLS/SLM processes was developed, based on the binding mechanism occurring in the process, in contrast with traditional classifications based on the processed material or the application. A broad range of commercial and experimental SLS/SLM processes – found from recent articles as well as from own experiments – was used to explain the different binding mechanism categories.

SLS/SLM processes can be classified into four main binding mechanism categories, namely “solid state sintering”, “chemically induced binding”, “liquid phase sintering – partial melting” and “full melting”. Most commercial processes can be classified into the latter two categories, which are therefore subdivided. The binding mechanism largely influences the process speed and the resulting part properties.

The classification presented is not claimed to be definitive. Moreover some SLM/SLM processes could be classified into more than one category, based on personal interpretation.

This paper can be a useful aid in understanding existing SLS/SLM processes. It can also serve as an aid in developing new SLS/SLM processes.

This paper aims to present a systematic approach in the literature survey related to metal additive manufacturing (AM) processes and its multi-physics continuum modelling approach for its better understanding.

A systematic review of the literature available in the area of continuum modelling practices adopted for the powder bed fusion (PBF) AM processes for the deposition of powder layer over the substrate along with quantification of residual stress and distortion. Discrete element method (DEM) and finite element method (FEM) approaches have been reviewed for the deposition of powder layer and thermo-mechanical modelling, respectively. Further, thermo-mechanical modelling adopted for the PBF AM process have been discussed in detail with its constituents. Finally, on the basis of prediction through thermo-mechanical models and experimental validation, distortion mitigation/minimisation techniques applied in PBF AM processes have been reviewed to provide a future direction in the field.

The findings of this paper are the future directions for the implementation and modification of the continuum modelling approaches applied to PBF AM processes. On the basis of the extensive review in the domain, gaps are recommended for future work for the betterment of modelling approach.

This paper is limited to review only the modelling approach adopted by the PBF AM processes, i.e. modelling techniques (DEM approach) used for the deposition of powder layer and macro-models at process scale for the prediction of residual stress and distortion in the component. Modelling of microstructure and grain growth has not been included in this paper.

This paper presents an extensive review of the FEM approach adopted for the prediction of residual stress and distortion in the PBF AM processes which sets the platform for the development of distortion mitigation techniques. An extensive review of distortion mitigation techniques has been presented in the last section of the paper, which has not been reviewed yet.

The cooling process of polymer components fabricated by selective laser sintering (SLS) plays a vital role in determining the crystallinity, density and the resultant properties of the produced parts. However, the control and optimization of the cooling process remains challenging. The purpose of this paper is to therefore investigate the cooling process of the SLS fabricated polyamide 12 (PA12) components through simulations. This work provides necessary fundamental insights into the possibilities for optimization and control of this cooling process for achieving desired properties.

The thermal properties of the PA12 powder and SLS fabricated PA12 components including density, specific heat and thermal conductivity were first determined experimentally. Then, the finite element method was used to optimize a container (a cuboid aluminum box where PA12 parts are built by the SLS) geometry in which the SLS parts can cool down in a controlled manner. Also, the cooling parameters required for maximum temperature homogeneity and minimum cooling time were determined.

Two different approximations in the finite element (FE) model were used and compared. It was found that the approximation which considers powder as a solid medium with porous material properties gives better results as compared to the approximation which treats powder as a collection of air and particles with solid material properties. The results also showed that the geometry of the containers has an important influence on the cooling process of the SLS fabricated PA12 components regarding temperature homogeneity and cooling time required. A container with a small width, long length and high height tends to result in a more homogenous temperature distribution during the cooling process.

Thermal constants of PA12 powder and parts were accurately determined as a starting point for numerical simulations. The FE model developed in this work provides useful and necessary information for the optimization and control of the cooling process of the SLS fabricated PA12 components and can thus be used for ensuring high-quality products with desired component properties.

This paper aims to present a possible complete set of dimensionless parameters to describe the process of selective laser melting (SLM). This makes it possible to compare the similarity between different experiments, a sine‐qua‐non for a correct comparison of the results.

The paper describes the application of dimensional analysis to SLM.

Although the idea of dimensionless numbers is far from new, it has apparently never been applied rigorously to rapid prototyping and rapid manufacturing technologies. The technique is important, since it reduces the number of factors and makes it possible to compare results of different research groups. Furthermore, some more fundamental insights about the process can be gained.

This work is a first step towards a manageable system to control very difficult processes.

The purpose of this paper is to propose and evaluate the selection of materials for the selective laser sintering (SLS) process, which is used for low-volume production in the engineering (e.g. light weight machines, architectural modelling, high performance application, manufacturing of fuel cell, etc.), medical and many others (e.g. art and hobbies, etc.) with a keen focus on meeting customer requirements.

The work starts with understanding the optimal process parameters, an appropriate consolidation mechanism to control microstructure, and selection of appropriate materials satisfying the property requirement for specific application area that leads to optimization of materials.

Fabricating the parts using optimal process parameters, appropriate consolidation mechanism and selecting the appropriate material considering the property requirement of applications can improve part characteristics, increase acceptability, sustainability, life cycle and reliability of the SLS-fabricated parts.

The newly proposed material selection system based on properties requirement of applications has been proven, especially in cases where non-experts or student need to select SLS process materials according to the property requirement of applications. The selection of materials based on property requirement of application may be used by practitioners from not only the engineering field, medical field and many others like art and hobbies but also academics who wish to select materials of SLS process for different applications.

Ti6Al4V alloy has received a great deal of attention in medical applications due to its biomechanical compatibility. However, the human bone stiffness is between 10 and 30 GPa while solid Ti6Al4V is several times stiffer, which would cause stress shielding with the surrounding bone, which can lead to implant and/or the surrounding bone’s failure.

In this work, the effect of selective laser melting (SLM) process parameters on the characteristics of Ti6Al4V samples, such as porosity level, surface roughness, elastic modulus and compressive strength (UCS), has been investigated using response surface method. The examined ranges of process parameters were 35-50 W for laser power, 100-400 mm/s for scan speed and 35-120 µm for hatch spacing. The process parameters have been optimized to obtain structures with properties very close to that in human bones.

The results showed that the porosity percentage of a SLM component could be increased by reducing the laser power and/or increasing the scan speed and hatch spacing. It was also shown that there was a reverse relationship between the porosity level and both the modulus of elasticity and UCS of the SLM part. In addition, the increased laser power was resulted into a substantial decrease of the surface roughness of SLM parts. Results from the optimization study revealed that the interaction between laser process parameters (i.e. laser power, laser speed, and the laser spacing) have the most significant influence on the mechanical properties of fabricated samples. The optimized values for the manufacturing of medical implants were 49 W, 400 mm/s and 99 µm for the laser power, laser speed and laser spacing, respectively. The corresponding porosity, surface roughness, modulus of elasticity and UCS were 23.62 per cent, 8.68 µm, 30 GPa and 522 MPa, respectively.

Previous investigations related to additive manufacturing of Ti alloys have focused on producing fully dense and high-integrity structures. There is a clear gap in literature regarding the simultaneous enhancement and adjustment of pore fraction, surface and mechanical properties of Ti6Al4V SLM components toward biomedical implants. This was the objective of the current study.

To find the suitable parameters for selective laser sintering (SLS) of selected ferro‐based powders. These parameters will help to create products having appreciable strength shown by the highest density and good surface property.

Design of experiment (L9 Taguchi design) has been used to obtain the parameters in the minimum possible number of experiments. For finding the range of various parameters selected such as scan speed, scan spacing and layer thickness, some preliminary experiments have been performed. In order to carry out varied characterization for a given type of experiment, a number of samples have been made.

An attempt has been made to observe the correlation between applied laser energy and the properties of the laser‐sintered parts. Taguchi design has been useful and has given the optimized parameters. It has also been found that the infiltration increases the strength of the part substantially compared with the property of end‐used sintered product.

The present set of experiments was limited by the range of supplied laser energy to the powder system, as the laser power could not be increased.

There is a need to search for alternative powders for manufacturing parts through SLS, which can alleviate the need to depend on customized powders, as these customized powders are limited to be used only with prescribed commercial SLS machines for their best performance. This drawback restricts their general use independent of any particular machine and it is, therefore, required to develop know‐how of powders and related process parameters for SLS. The present work is an effort in this direction in which laser sintering of a specially developed iron‐based powder mixture (Fe, Ni, Cu and Fe₃P) has been tested on an SLS machine.

This paper aims to establish the microstructures and the process-structure relationships in duplex stainless steel powders consolidated by selective laser melting (SLM).

A priori data on energy density levels most appropriate to consolidation of duplex stainless steel powders through SLM served as the basis to converge on the laser settings. Experimental designs with varying laser power and scan speeds and test pieces generated allowed metallographic evaluations based on optical and scanning electron microscopy and electro backscatter diffraction analyses.

Duplex stainless steel powders are established for processing by SLM. However, the dynamic point heat source and associated transient thermal fields affect the microstructures to be predominantly ferritic, with grains elongated in the build direction. Austenite precipitated either at the grain boundaries or as Widmanstätten laths, whereas the crystallographic orientations and the grain growth are affected around the cavities. Considerable CrN precipitation is also evidenced.

Duplex stainless steels are relatively new candidates to be brought into the additive manufacturing realm. Considering the poor machinability and other difficulties, the overarching result indicating suitability of duplex powders by SLM is of considerable value to the industry. More significantly, the metallographic evaluation and results of the current research allowed further understanding of the material consolidation aspects and pave ways for fine tuning and establishment of the process-structure-property relationships for this important process-material combination.